Reply To: How To/Heated bed not working

New Home Forum Getting Started How To/Heated bed not working Reply To: How To/Heated bed not working

#19636
Profile photo of PureField
PureField
Participant

Did not get to capture the screens before I started the autotune process per http://reprap.org/wiki/Heatbeds_-_A_beginner's_guide and get a few errors:

`21:56:17.166 : Printer reset detected – initalizing
21:56:17.166 : start
21:56:17.170 : echo:Marlin 1.1.0-RC7
21:56:17.170 : echo: Last Updated: 2016-07-31 12:00 | Author: (none, default config)
21:56:17.170 : Compiled: Oct 17 2016
21:56:17.174 : echo: Free Memory: 3255 PlannerBufferBytes: 1232
21:56:17.179 : Error:EEPROM checksum mismatch
21:56:17.179 : echo:Hardcoded Default Settings Loaded
21:56:17.179 : echo:Steps per unit:
21:56:17.182 : echo: M92 X200.00 Y200.00 Z4535.44 E200.00
21:56:17.183 : echo:Maximum feedrates (mm/s):
21:56:17.187 : echo: M203 X190.00 Y190.00 Z8.50 E25.00
21:56:17.187 : echo:Maximum Acceleration (mm/s2):
21:56:17.187 : echo: M201 X500 Y500 Z35 E10000
21:56:17.191 : echo:Accelerations: P=printing, R=retract and T=travel
21:56:17.191 : echo: M204 P400.00 R3000.00 T500.00
21:56:17.199 : echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)
21:56:17.203 : echo: M205 S0.00 T0.00 B20000 X4.00 Z0.40 E5.00
21:56:17.203 : echo:Home offset (mm)
21:56:17.203 : echo: M206 X0.00 Y0.00 Z0.00
21:56:17.208 : echo:Material heatup parameters:
21:56:17.208 : echo: M145 S0 H190 B50 F0
21:56:17.208 : echo: M145 S1 H240 B110 F0
21:56:17.208 : echo:PID settings:
21:56:17.212 : echo: M301 P17.98 I0.98 D83.62
21:56:17.212 : echo: M304 P10.00 I0.02 D305.40
21:56:17.212 : echo:Filament settings: Disabled
21:56:17.215 : echo: M200 D3.00
21:56:17.215 : echo: M200 D0
21:56:17.311 : N1 M110*34
21:56:17.311 : N2 M115*36
21:56:17.311 : N4 M114*35
21:56:17.330 : N5 M111 S6*98
21:56:17.331 : N6 T0*60
21:56:17.331 : N7 M20*22
21:56:17.331 : N8 M80*19
21:56:22.918 : FIRMWARE_NAME:Marlin 1.1.0-RC7 (Github) SOURCE_CODE_URL:https://github.com/MarlinFirmware/Marlin PROTOCOL_VERSION:1.0 MACHINE_TYPE:MPCNC EXTRUDER_COUNT:1 UUID:xxx
21:56:22.918 : N11 M220 S100*81
21:56:22.921 : N12 M221 S100*83
21:56:22.922 : X:0.00 Y:0.00 Z:0.00 E:0.00 Count X: 0 Y:0 Z:0
21:56:22.922 : N13 M111 S6*85
21:56:22.922 : echo:DEBUG:INFO,ERRORS
21:56:22.924 : N14 T0*15
21:56:22.926 : echo:Active Extruder: 0
21:56:22.926 : Begin file list
21:56:22.926 : End file list
21:56:22.930 : Error:No Line Number with checksum, Last Line: 11
21:56:22.930 : Error:Line Number is not Last Line Number+1, Last Line: 11
21:56:22.930 : Resend: 12
21:56:22.935 : Resend: N12 M221 S100*83
21:56:22.935 : Resend: N13 M111 S6*85
21:56:22.935 : Resend: N14 T0*15
21:56:23.017 : echo:DEBUG:INFO,ERRORS
21:56:23.017 : echo:Active Extruder: 0
21:56:50.235 : N24 M303 E-1 C8 S90*77
21:56:50.239 : PID Autotune start
22:06:50.640 : PID Autotune failed! timeout
22:06:50.641 : N33 M104 T0 S205*22
22:06:50.643 : N34 M104 T0 S0*22
22:06:50.647 : Error:No Line Number with checksum, Last Line: 31
22:06:50.651 : Error:Line Number is not Last Line Number+1, Last Line: 31
22:06:50.651 : Resend: 32
22:06:50.656 : Resend: N33 M104 T0 S205*22
22:06:50.656 : Resend: N34 M104 T0 S0*22