- Wesley GardnerParticipantJanuary 24, 2016 at 11:48 amPost count: 12
1) Did you buy everything from here? Nope 🙁
a)If you didn’t or changed some things please don’t leave out any details. (purchased all recommended items from your list)
b)What firmware? Marlin_16_32_090615_therm
2) Are you using end stops? no
3) Are you using all my recommended parts? yes
So having a issue not sure if power supply or I have to wait for the jumpers to arrive for the cnc shield but seems when power to the cnc shield the power light only flickers on the brick I had to crack it open to make sure it was flickering seems power is getting to unit but will not kick in.
I have repetier host that I used so I know its connected to the software computer correctly used it since it was the same software I use for my 3d printer.
so based on my pictures and the info provided someone can lead me in the right direction, if its just a jumper issue I will be greatly awaiting their arrival.
Attachments:vicious1KeymasterJanuary 24, 2016 at 3:15 pmPost count: 2639
Is your red wire really the negative?Wesley GardnerParticipantJanuary 24, 2016 at 3:55 pmPost count: 12
ya I opened up the case as well and its labeled negative, and white is positivevicious1KeymasterJanuary 24, 2016 at 4:07 pmPost count: 2639
I would check it with a multimeter, unplug it from the board and verify it says 12V+. I have that board but never assembled it, you should be able to verify the board is okay by flashing the chip.
You could have a bad power supply, not likely but one of the easiest things to test.Wesley GardnerParticipantJanuary 24, 2016 at 5:51 pmPost count: 12
ok pulled off the board and its running 12.27v and light when up green when testing so going to go over the board and double check it. I am wondering if they miss printed the board as well, possibly red is positive will look into that more will pop open the power supply after as well.Wesley GardnerParticipantJanuary 24, 2016 at 10:17 pmPost count: 12
So looks like the power was not as it was printed motor engaged this time can feel it tighten up now but still no control going on might be repetier host time to play some moreWesley GardnerParticipantJanuary 24, 2016 at 10:38 pmPost count: 12
ok so I am getting somewhere now….. but obviously missing something.
Attachments:Wesley GardnerParticipantJanuary 24, 2016 at 10:39 pmPost count: 12
here is some more
Attachments:vicious1KeymasterJanuary 25, 2016 at 11:57 amPost count: 2639
I’m not sure repetier works with grbl. Did you flash your board yet or does it come pre-programmed?Wesley GardnerParticipantJanuary 25, 2016 at 3:00 pmPost count: 12
I thought it was pre-programmed…. going to have to load it up and check here as soon as I can.vicious1KeymasterJanuary 25, 2016 at 3:05 pmPost count: 2639
If it didn’t come with jumpers I doubt the arduino was programmed.Wesley GardnerParticipantJanuary 25, 2016 at 3:05 pmPost count: 12
Universal G-code Sender is what ill try out next as well. since I know that one will workWesley GardnerParticipantJanuary 25, 2016 at 10:54 pmPost count: 12
so after a bunch of talking with you and plotting out my next moves, I have made progress.
removed the arduino mega from the equation seems the windows xp machine I had the usb serial driver for it was a joke
hooked up my arduino uno sent the grbl firmware with xloader and it took both on boards btw
hooked up the sheild to it and loaded Universal G-code Sender and we have motion!
then I tried out a few other senders grblControl seems to be a nice one in my opinion so will play with that more.
onto the next step getting the rest of the motors hooked and ready to rock.
now I have a arduino mega for another project win win.
thanks for the help
You must be logged in to reply to this topic.