Advice – MPCNCNew Home › Forum › Mostly Printed CNC – MPCNC › Advice – MPCNCThis forum contains 105 topics and 501 replies, and was last updated by Brian 1 minute ago.Viewing 30 topics - 1 through 30 (of 105 total)1 2 … 4 →TopicVoicesPostsFreshness Flat Bottom Engraving Bits ?? Started by: Brian34 1 minute ago Brian spindle & VFD combo?? Started by: Gordon Steeves57 4 hours, 1 minute ago David Central carriage modifications Started by: Dui, ni shuo de dui722 8 hours, 16 minutes ago vicious1 Estlcam – Optimized Islands? Started by: Mic Vee35 20 hours, 38 minutes ago Mic Vee Xbox 360 Power Supply Started by: John34 1 day, 1 hour ago Bill Aluminium tube ? Started by: HOFMAN Stephane412 1 day, 5 hours ago HOFMAN Stephane MPCNC and CURA Started by: Ralph22 1 day, 9 hours ago vicious1 ESTLCAM tries to machine entire surface Started by: Rick Davis33 1 day, 22 hours ago Brian Estlcam and RUMBA board Started by: Walter Rotter39 2 days, 2 hours ago Walter Rotter Can this zero and corner finder be used with mpcnc with repetier? Started by: Sorrentino34 2 days, 7 hours ago P3DCNC Decimal inch is better! Started by: Fingerss35 2 days, 7 hours ago vicious1 Advice needed – CNC Started by: DanielP22 2 days, 10 hours ago vicious1 Cutting Carbon fiber Started by: John46 2 days, 13 hours ago Barry Some Old Guy Coding – Tool Change Started by: vicious1510 2 days, 23 hours ago Martin DB M4 instead of m3.5 Started by: Walter Rotter34 3 days, 13 hours ago Walter Rotter Plastic sticking to bits Started by: Tom Cole24 4 days, 6 hours ago Tom Cole How do I controll the CNC? Estlcam, Repetier, Fusion 360 Started by: Jens526 4 days, 8 hours ago Bill MPCNC Ability: What is the hardest material that can be reliably milled? Started by: Daniel Brown23 4 days, 21 hours ago Daniel Brown Alternative Nema 17 Steppers Started by: Adnan22 5 days, 2 hours ago Pavel Dust shoe and dust collection Started by: Dui, ni shuo de dui711 5 days, 11 hours ago Dui, ni shuo de dui printed XY with two perimeters Started by: Derek P22 6 days, 6 hours ago vicious1 max spindle weight Started by: Joe13 1 week ago Joe Overlaying text in Estlcam Started by: Zeenon525 1 week ago Brian Tool change during a job: How are you doing it? Started by: Dui, ni shuo de dui33 1 week ago Tom Cole Hardest material possible to cut? Started by: Walter Rotter56 1 week, 1 day ago Saaif Estlcam toolpath orders Started by: Brian622 1 week, 1 day ago Saaif Kress diy speed control Started by: Medmike25 1 week, 1 day ago Medmike Quieting Your Dust Colection Started by: P3DCNC33 1 week, 2 days ago Bradley F Estlcam questions Started by: Zeenon24 1 week, 4 days ago Zeenon Where to buy a RAMPS 1.4 Shield Started by: Chad23 1 week, 4 days ago Chad Viewing 30 topics - 1 through 30 (of 105 total)1 2 … 4 →You must be logged in to create new topics.