Troubleshooting – MPCNCNew Home › Forum › Mostly Printed CNC – MPCNC › Troubleshooting – MPCNCThis forum contains 467 topics and 3,049 replies, and was last updated by Sorrentino 49 minutes ago.Viewing 31 topics - 1 through 30 (of 468 total)1 2 … 16 →TopicVoicesPostsFreshness Best way to get help and get up and running fast. Started by: vicious111 1 year, 3 months ago vicious1 Seems like estlcam is giving z rapid f2100 speed Started by: Sorrentino12 49 minutes ago Sorrentino Compiler error Started by: Steven Weeks22 7 hours, 21 minutes ago Bill Flickering Graphic Smart Controller Started by: Alex_A22 7 hours, 50 minutes ago Bill Wiring issue Started by: Narvi36 1 day, 4 hours ago Narvi Jerky movement on x and y axis Started by: Zach T616 1 day, 11 hours ago Bryan Stepper Motor Heat Started by: Dan29 2 days, 22 hours ago Dan Inconsistent Cuts Started by: gbiski616 3 days, 6 hours ago Vincent Pollaro How to extend hotend wire of extruder? Started by: aravinth23 3 days, 6 hours ago aravinth Turn off port P4 after connection power or reset Started by: Koen11 3 days, 11 hours ago Koen PC connection issues Started by: Sarah Martens417 3 days, 12 hours ago Barry Inaccurate travel dimensions (esp. Z) Started by: Michael Wafler22 4 days, 9 hours ago vicious1 Commenting out the LCD part… Maybe I'll get one if I get it up and running Started by: John47 5 days, 5 hours ago Barry Dimensional Accuracy on Y Axis Started by: usernamesarehardtothinkup24 5 days, 21 hours ago vicious1 Inconsistent Cuts Part 2 Started by: Zeenon22 6 days ago vicious1 Home button in Repetier, moving x and y without power, lcd not doing much Started by: Zach T616 6 days ago vicious1 Z axis gone bad Started by: Dalton Porter712 6 days, 1 hour ago Bill How to set (relative?) home position? Started by: OmegaII57 6 days, 1 hour ago vicious1 Motor strength Started by: andrej34 6 days, 18 hours ago WarHawk8080 Firmware Differences Started by: Kris36 6 days, 19 hours ago WarHawk8080 Fusion 360 Tool settings for 45 degree V-bit Started by: Gurft23 6 days, 21 hours ago vicious1 LCD Axis Control increments = 4 times what they should me Started by: Will23 1 week ago Joe bumpy axis Started by: Arthur Padget411 1 week, 1 day ago Barry Z-axis Still giving me a problem after everything 1 2 Started by: Matt1050 1 week, 2 days ago P3DCNC Z Axis moving only in 1 direction Started by: Chris27 1 week, 3 days ago vicious1 CNC randmoly stops when using shop vac Started by: Dui, ni shuo de dui1015 1 week, 3 days ago Or Green Old part request Started by: John22 1 week, 3 days ago vicious1 MPCNC 8mm rod Firmware trouble Started by: Alex Alexandru411 1 week, 4 days ago vicious1 Z-axis shifts up or down more than it should Started by: Glenn212 1 week, 4 days ago Glenn RC7 vs RC6 Y Direction Started by: Herman Meyer22 1 week, 4 days ago vicious1 Laser driver issue Started by: Justin23 1 week, 5 days ago Justin Viewing 31 topics - 1 through 30 (of 468 total)1 2 … 16 →You must be logged in to create new topics.