helifriz's build

New Home Forum LowRider Your Builds – LowRider helifriz's build

This topic contains 15 replies, has 5 voices, and was last updated by Profile photo of helifriz helifriz 4 weeks ago.

Viewing 16 posts - 1 through 16 (of 16 total)
  • Author
    Posts
  • #27920
    Profile photo of helifriz
    helifriz
    Participant

    I have finally got it mounted. hopefully tomorrow I will have it rolling under its own power.

    #27925
    Profile photo of vicious1
    vicious1
    Keymaster

    Nice!!!

    On the lower rollers the bolts look short, did I screw that up or did you just have some shorty bolts? Sorry I am nervous as these builds are getting close to completion the errors could start showing up.

    #27927
    Profile photo of helifriz
    helifriz
    Participant

    I used all the bolt dimensions you recommended. I used 3/8inch ply. So I feel that is why they are short. I did end up using more 6/32 1 inch rather than 3/4. Even after counter sinking they were short. I still ned to replace some of the 3/4 inch. You can see 1inch on the X. 3/4 on the Z. and 1 inch through the Z/M corner I feel they are too short.

    Attachments:
    #27930
    Profile photo of vicious1
    vicious1
    Keymaster

    Okay the 3/8 explains it.

    #27947
    Profile photo of Barry
    Barry
    Participant

    Nice! You are probably the closest to being finished with the lowrider build!

    #28122
    Profile photo of helifriz
    helifriz
    Participant

    It moves.

    Low Rider

    #28124
    Profile photo of vicious1
    vicious1
    Keymaster

    Hell yes!!!!!

    PLease please please drop that on youtube. That is the only way I can add it to the playlist. So stoked, Proof it actually works!

    #28127
    Profile photo of Barry
    Barry
    Participant

    That’s freaking awesome!

    #28130
    Profile photo of Martin DB
    Martin DB
    Participant

    Congratulations! When we will see it in action?

    #28131
    Profile photo of helifriz
    helifriz
    Participant

    Will this work.

    youtube

    I need a bigger garage. Hopefully I will do some cutting real soon..

    #28216
    Profile photo of helifriz
    helifriz
    Participant

    First cut…. 3 hour job and a bit change..

    Its frikn awesome…

    Youtube

    #28217
    Profile photo of vicious1
    vicious1
    Keymaster

    OMG!!!!!

    #28218
    Profile photo of vicious1
    vicious1
    Keymaster

    So I need to get some wire management shots for you but I have everything in between the panels and out the bottom into the ramps, and the power supply brick fits in there as well on top of the adjustable roller.

    Nothing against what you have there just how I do it.

    So stoked I’m texting it to all my friends and fam.

    #28219
    Profile photo of Martin DB
    Martin DB
    Participant

    Good job!

    #28226

    Great machine.
    How do you ensure your table stays flat everywhere?

    #28249
    Profile photo of helifriz
    helifriz
    Participant

    *Ryan Thnaks for the tip on the wire management.. I will get onto tidying up the wires ASAP!!

    *Dui I was thinking of placing my spoiler board and levelling/milling the board to the machine.

    Same video but 4k (well kind of)

    youtube

    • This reply was modified 4 weeks ago by Profile photo of helifriz helifriz.
Viewing 16 posts - 1 through 16 (of 16 total)

You must be logged in to reply to this topic.