RC7_MPCNC_LCD_9916. No heated bed

New Home Forum Mostly Printed CNC – MPCNC Troubleshooting – MPCNC RC7_MPCNC_LCD_9916. No heated bed

This topic contains 4 replies, has 2 voices, and was last updated by  bern 8 months, 1 week ago.

Viewing 5 posts - 1 through 5 (of 5 total)
  • Author
    Posts
  • #29152

    bern
    Participant

    https://www.vicious1.com/wp-content/uploads/2015/12/RC7_MPCNC_LCD_9916.zip

    How to enable heated bed in marlin RC7 Mpcnc w/ LCD. Does not show in repetier host, only heated Extruder shown.

    #29167

    Ryan
    Keymaster

    You have to enable the bed thermistor near the top of the config.h in the firmware. Then reflash your arduino.

    #29204

    bern
    Participant

    Hi.. can’t seem to find it, can you show which line in the firmaware.

    Thanks

    #29237

    Ryan
    Keymaster

    //#define DUMMY_THERMISTOR_999_VALUE 100
    // :{ ‘0’: “Not used”,’1′:”100k / 4.7k – EPCOS”,’2′:”200k / 4.7k – ATC Semitec 204GT-2″,’3′:”Mendel-parts / 4.7k”,’4′:”10k !! do not use for a hotend. Bad resolution at high temp. !!”,’5′:”100K / 4.7k – ATC Semitec 104GT-2 (Used in ParCan & J-Head)”,’6′:”100k / 4.7k EPCOS – Not as accurate as Table 1″,’7′:”100k / 4.7k Honeywell 135-104LAG-J01″,’8′:”100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT”,’9′:”100k / 4.7k GE Sensing AL03006-58.2K-97-G1″,’10’:”100k / 4.7k RS 198-961″,’11’:”100k / 4.7k beta 3950 1%”,’12’:”100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)”,’13’:”100k Hisens 3950 1% up to 300°C for hotend ‘Simple ONE ‘ & hotend ‘All In ONE'”,’20’:”PT100 (Ultimainboard V2.x)”,’51’:”100k / 1k – EPCOS”,’52’:”200k / 1k – ATC Semitec 204GT-2″,’55’:”100k / 1k – ATC Semitec 104GT-2 (Used in ParCan & J-Head)”,’60’:”100k Maker’s Tool Works Kapton Bed Thermistor beta=3950″,’66’:”Dyze Design 4.7M High Temperature thermistor”,’70’:”the 100K thermistor found in the bq Hephestos 2″,’71’:”100k / 4.7k Honeywell 135-104LAF-J01″,’147′:”Pt100 / 4.7k”,’1047′:”Pt1000 / 4.7k”,’110′:”Pt100 / 1k (non-standard)”,’1010′:”Pt1000 / 1k (non standard)”,’-3′:”Thermocouple + MAX31855 (only for sensor 0)”,’-2′:”Thermocouple + MAX6675 (only for sensor 0)”,’-1′:”Thermocouple + AD595″,’998′:”Dummy 1″,’999′:”Dummy 2″ }
    #define TEMP_SENSOR_0 11 //MPCNC
    #define TEMP_SENSOR_1 0
    #define TEMP_SENSOR_2 0
    #define TEMP_SENSOR_3 0
    #define TEMP_SENSOR_BED 0

    Change the last zero to 11 from most common thermistors.

    #29279

    bern
    Participant

    #define TEMP_SENSOR_BED 11

    Got it.. thanks Sir

Viewing 5 posts - 1 through 5 (of 5 total)

You must be logged in to reply to this topic.